Generic selectors
Exact matches only
Search in title
Search in content

8 Gasket Myths – Debunked

Durlon
Durlon 8 Gasket Myths - Debunked

8 Gasket Myths – Debunked

Whether it is material selection, installation, or trouble-shooting gasket failures, there are many common things we hear people talk or ask about. So, let’s try and clear the air and help shed some truth on common things that are either thought to be true or practiced in the field.

  1. Thicker gasket material is better
    People generally request thicker material due to an excessive gap or misaligned flanges. They think that the thicker material will fill the void; however, what they may not be aware of is creep/relaxation. Gasket creep/relaxation is somewhat linear (depending on the material) and the amount of material creep increased with gasket thickness. Want less creep, go thin or go home! Also, things such as torque retention, higher blow-out resistance, and leakage (through gasket permeation) are much better with thinner materials.
  2. Gasket colors indicate the materials are the same
    ”I’ve always used a blue gasket, so I need a blue gasket” is a common phrase heard time and time again. Gasket color is generally meaningless. But in some cases, competitors may choose the same color for their entire product line. So, to be sure, instead of asking for a specific color, verify the pressure, temperature, and media so that the proper material will be selected for your application.
  3. Torque values are the same for all gasket materials
    All torque values are not the same. Firstly, when looking at torque charts please be sure to read the fine print to verify bolting material, % of bolt yield used, K-Factor used, and the maximum allowed compression for each material. For most soft gaskets, the maximum gasket compression is 15,000psi, however, for semi-metallic gaskets like SWG’s and Kammprofile’s the maximum compression is more like 20,000-30,000 psi so there is a good chance you could possibly crush the gasket if you use an incorrect value.
  4. Leaking gaskets just need to be re-tightened
    If a gasket is leaking, do not re-tighten. Particularly with soft gasket materials, hot torquing is very dangerous. Once compressed gaskets reach an elevated temperature they can become brittle and further tightening can cause the gasket to crack. This can further increase the leak or even worse, cause a gasket blow out! If a gasket is leaking, it should be replaced!
  5. All gaskets are made the same and perform the same
    Not true. There are many types of methods for the manufacturing of sheet materials such as the calendar method, skived method and even the beater add which all give the material different properties. The properties shown on gasket technical data sheets are for QC purposes and allow you to somewhat compare “apples to apples” however they do not actually give you performance data but are merely indicators on how they may perform in certain applications.
  6. Grease or lubricant is a good way to hold a gasket in place during the installation process
    Getting a gasket into position during an installation can be tricky, so sometimes people use a dab of grease or lube on the gasket to get it to stick to the sealing face during bolt up. This is not a good idea for two reasons: the grease can chemically attack the gasket material and it also lubricates the sealing face which allows the gasket to be pushed out easier by the system pressure. Now, remember, we are trying to compress the gasket enough to fill the flange serrations and have them “bite into” the gasket to resist being pushed out by the system pressure. Putting grease on the gasket negates what we are trying to achieve…..so don’t do it!
  7. Softer materials seal better
    Firmness is also referred to as the materials ability to resist flow. Softer materials are not necessarily better, but they are good for applications where the material needs to confirm to worn flanges or uneven flanges. It is quite common for the material to have more creep when softer, so this may not be a desirable trade-off when choosing the material. For higher temperature and higher pressure applications, material hardness and sealing surface finish need to be strongly considered.
  8. Gasket installation procedure doesn’t affect sealing performance
    Gasket installation is the most influential factor that affects sealing performance. If you do not install the gasket using a correct method such as the Legacy Method (see figure above), an alternative method listed in ASME PCC-1, Appendix F or the method recommended from the manufacturer, you run the risk of not getting the most out of your gasket. Using a proper installation method helps the installer bring the flanges together in parallel which lessens the risk or crushing the gasket or unevenly loading the gasket which can cause leaks. Furthermore, it ensures that the load applied to the gasket (via torquing) is correct and consistent which is important in gasket sealing performance.

Download a handy reference sheet from Durlon® Sealing Solutions to properly tighten bolts during gasket installation.

Related Articles

Related Whitepapers

10 Tips To Improve Operations Of A Salt Water Disposal Pump

In the oil and gas industry, a large amount of salt water is collected during the process of oil production. In Texas, for example, the…

Cavitation Guide

Cla-Val has the technical resources you need to design and operate a fluid handling system that is both efficient and reliable. You can visit a…

Managing Aging Plants, Equipment & Infrastructure

Solving your challenges with proven solutions Chesterton is a full-solution provider for water treatment/wastewater plants and systems that are seeking to increase equipment reliability and…

Reliable Pumps for High-pressure Cleaning with Superior Handling of Abrasives and Particulates

Compact, Seal-less Pumps for Reliable Operation and Long Service Life With more than 40 years of experience serving many different industries, including major global companies,…

Comments

Leave a Reply

Your email address will not be published. Required fields are marked *

Sign up for our Newsletter!


By submitting this form, you are consenting to receive marketing emails from: Empowering Pumps & Equipment, 2205-C 7th Street, Tuscaloosa, AL, 35401, http://www.empoweringpumps.com. You can revoke your consent to receive emails at any time by using the SafeUnsubscribe® link, found at the bottom of every email. Emails are serviced by Constant Contact